![]() It would also provide more security because breaking into this toolbox would be more difficult with better hinges. The cost of using better materials here would be minimal and well worth the investment. As an obvious design flaw, I am more concerned about the longevity of the plastic hinges. The hinges must be made of more robust materials such as stamped steel or aluminum. There are two suggestions for improving the SwingCase Truck Storage Box. It is better to read how to clean and maintain the toolbox by reading: How to Clean Aluminum Tool Box – Handy Information You Need?Ĭheck Price on Amazon Recommendations | Undercover Swing Case Problems However, on the wrong side, the locking latch does not pull down tight enough to compress to foam and form a water-resistant seal. The Swingcase has a foam seal around the entire edge of the lid. However, this was not a big issue as we usually have to roll up the tonneau cover before opening the case, but it is worth pointing out. ![]() One drawback I noticed on the passenger side is if you have installed a tonneau cover, it creates an obstacle in fully opening the swing case. It rotates to 180 degrees which makes access easy and reachable. The lever is easy to access when you stand near the tailgate. To open the case, you must pull the lever and the case wings out. The UnderCover Swing Case has a simple yet elegant and practical design. It creates a metal-on-metal attachment point that makes it more secure. What I like about this swing case toolbox is its excellent spot for an optional padlock. Note: The screw must be precisely tightened before installation. The inside case is metal and set in place with a serrated head-locking screw. Let me tell you about the inside case material. The cover stops the snow and water from pooling inside the exposed swing case toolbox because nothing is worse than a freezing lock preventing you from accessing the swing case. I admire the quality of the latch and turning latch bezel crafted with a metal material. It has a locking latch system that functions as a lock and a latch to open and close the case. The SwingCase cover is made with metal hinges. Read in detail about: Is Tool Box and Bed Cover Combo good? Security The driver-side swing case mainly uses for hand tools, whereas the passenger-side swing case uses for straps and rods. Moreover, I am happy to announce that the Swing Case could fit almost every tool you require. It can hold upto 75 lbs pounds of weight. The swing case is sturdy and robust yet lightweight. The rotation makes access easy to reach the tools and tray of the swing case. The UnderCover Swing Case toolbox has a quick-release latch system that can rotate about 180 degrees and swing back into the position over the wheel wall for maximum bed access. This technique allows you to use the tie-down point if you temporarily remove the swing case toolbox. Next, unbolt the already installed tie-down plates and utilize the Torx head bolts to secure the latching plate right over the top of the tie-down plate. To install, open the tailgate to get access to the holes that are pre-drilled. It only takes 10-15 minutes with simple tools such as a socket set and a Torx head bit + screwdriver. The installation of the UnderCover swing case is a breeze. Special features: water resistant, sturdy, durable, convenient, safe, and helpful.Thanks.I've also ordered the cubby box that goes underneath the rear seat and molle seat covers with pouches for the back of the seat.UnderCover Swing Case is the only swinging, removable, and portable toolbox for trucks on the market.īefore diving into the detailed information, let me give you a quick rundown of its features and specifications. Wondering if anyone has seen anyone else try this and if additional steel plate had to be used underneath the bed for structural strength to the bed sheet metal? With regard to the comment about the rear tie down hooks, I'm considering moving the rear ones to the floor of the bed near tailgate. ![]() I'm assuming the swing out arm and mounting bracket are steel? I will have a shell on my truck, but after reading the posts about warping, if/when it occurs, I'm considering removing the plastic boxes, mounting large ammo cans to the brackets and fabricate them to fit over the wheel well (I weld and fabricate as a weekend hobby). Anyone here have one on the crew max 5'5" bed? Any fit issues? $240 SC400P | Fits 2007 - 2021 Toyota Tundra Passenger Side,Black SC400P) will work with the crew max 5'5" bed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |